we reserve the right to make changes to improve technical design and may do so without further notice. parameters can vary in different applications.all operating parameters must be validated for each customer application by the c ustomer. led - lamp 15.11.2007 rev. 05 radiation infrared note: special packages with standoff available on request maximum ratings t amb = 25c, unless otherwise specified symbol value unit i f 100 ma i fm 200 ma p d 150 mw t amb -20 to +80 c t stg -55 to +100 c soldering temperature t sd 260 c optical and electrical characteristics t amb = 25c, unless otherwise specified parameter test conditions symbol min typ max unit forward voltage i f = 20 ma v f 0.85 1.0 v forward voltage* i f = 100 ma v f 0.95 v reverse voltage i r = 100 a v r 5v radiant power i f = 20 ma e 1.6 2.2 mw radiant power* i f = 100 ma e 8.5 mw radiant intensity i f = 20 ma e 10 mw/sr radiant intensity* i f = 100 ma e 38 mw/sr peak wavelength i f = 20 ma p 1250 1300 1350 nm spectral bandwidth at 50% i f = 20 ma ? 0.5 70 nm viewing angle i f = 20 ma ? 25 deg. switching time i f = 20 ma t r, t f 10 ns note: all measurements carried out on epigap equipment power dissipation operating temperature range storage temperature range parameter forward current (dc) peak forward current (t p 50 s, t p /t = 1/2) optical communications, safety equipment, automation t 5 s, 3 mm from case ELD-1300-525 case 5 mm plastic lens technology ingaas/inp *measured after 30s current flow type mqw description applications high-power, high-speed infrared led in standard 5 mm package, housing without standoff leads test onditions 8,6 36,5 1,0 1,5 1 0,6 - 0,2 0,8 - 0,4 5,75 - 0,3 anode 2,54 ? 5 epigap optoelektronik gmbh, d-12555 berlin, k?penicker str.325 b, haus 201 tel.: +49-30-6576 2543, fax : +49-30-6576 2545 1 of 3
we reserve the right to make changes to improve technical design and may do so without further notice. parameters can vary in different applications.all operating parameters must be validated for each customer application by the c ustomer. led - lamp 15.11.2007 rev. 05 ELD-1300-525 800 1000 1200 1400 1600 1800 0,0 0,2 0,4 0,6 0,8 1,0 rel. intensity (arb. units) wavelength (nm) spectral power distribution (typical) at i f = 20 ma 0 20406080100 0 2 4 6 wavelength shift (nm) i f (ma) typical wavelength shift vs. forward current (rel. to p @ i f = 20 ma) epigap optoelektronik gmbh, d-12555 berlin, k?penicker str.325 b, haus 201 tel.: +49-30-6576 2543, fax : +49-30-6576 2545 2 of 3
we reserve the right to make changes to improve technical design and may do so without further notice. parameters can vary in different applications.all operating parameters must be validated for each customer application by the c ustomer. led - lamp 15.11.2007 rev. 05 ELD-1300-525 remarks concerning optical radiation safety* up to maximum forward current, at continuous operation, this led may be classified as led product class 1 , according to standard iec 60825-1:a2. class 1 products are safe to eyes and skin under reasonably predictable conditions. this implicates a direct observation of the light beam by means of optical instruments. *note: safety classification of an optical component mainly depends on the intended application and the way the component is being used. furthermore, all statements made to classification are based on calculations and are only valid for this led "as it is", and at continuous operation. using pulsed current or altering the light beam with additional optics may lead to different safety classifications. therefore these remarks should be taken as recommendation and guideline only. led class 1 accord. din en/iec 60825-1:2001-11 epigap optoelektronik gmbh, d-12555 berlin, k?penicker str.325 b, haus 201 tel.: +49-30-6576 2543, fax : +49-30-6576 2545 3 of 3
|
